Chromalox 2110 Instrukcja Użytkownika

2110 Temperature ControllerLoadAlarmPointTemp2110°F°CSet PointChromaloxCUSUL®User Manual0037-75409PK498-1May, 2012

Chromalox 21106Section 3–Installation and WiringMount the 21101. Cut out a 1/4 DIN, 3.6-inch (92mm) square hole in the mount-ing panel.2. Insert the u

2110 Temperature ControllerChromalox 21107Good Wiring PracticesSeparate wire into bundles—When planning the system wiring, separate wiring into functi

Chromalox 21108Section 3–Installation and WiringSensor Input WiringSensor Wiring NotesFor safety and best controller performance,• Sensor leads (ther

2110 Temperature ControllerChromalox 2110Three-Wire RTD InputsIMPORTANT: When making the three-wire RTD input connection, make the resistance of all t

Chromalox 2110Control Output WiringThe following figures show the proper control output wiring for the various 2110 configurations. R1 (1 Amp Relay) a

2110 Temperature ControllerChromalox 2110S1 (Solid State Relay, 5 Amps) and S2 (Solid State Relay, 10 Amps) Output WiringNote: 2110 model S2 has a fa

Chromalox 2110To access the user configuration menus, 1. Press and hold the and buttons. After three seconds the display will begin to toggle betwe

2110 Temperature ControllerChromalox 211013Section 4–Adjusting Set Point and Configuration4. Press the or buttons to adjust the value (only the val

Chromalox 2110Security Codes and LevelsTo limit access to the user configuration interface, security codes are assigned to different menu levels. Make

2110 Temperature ControllerChromalox 211015Section 4–Adjusting Set Point and ConfigurationConfiguration MenuscontinuedFor calibration menus (CoFF, dFLt,

Chromalox 2110Control OperationThe 2110 is shipped from the factory with PI (proportional/integral) con-trol. Proportional control actually determines

2110 Temperature ControllerChromalox 2110WARNING: Remove power from the controller before changing the output module. Failure to do so could cause dam

Chromalox 2110Module Installationcontinued18Section 6–Replacing Output ModulesAuto Cycle TimeThe Control Output Modules have a default cycle time of 1

2110 Temperature ControllerChromalox 2110Section 7—CalibrationCalibration offset offsets the displayed value. Usually, this option is used to match di

Chromalox 2110Factory Calibration RecoveryThis procedure allows you to return the controller to its factory calibration settings in the event it is se

2110 Temperature ControllerChromalox 2110Section 8—SpecificationsControl Modes ... ON/OFF; PI—Proportional with integralC

Chromalox 2110Section 9—TroubleshootingThe following Troubleshooting Guide offers simple solutions to common problems and explains the 2110’s Error Me

2110 Temperature ControllerChromalox 211023Section 9–TroubleshootingTroubleshootingcontinuedSymptom Probable Cause Correction StepsProcess not in cont

1347 HEIL QUAKER BLVD., LAVERGNE, TN 37086Phone: (615) 793-3900 www.chromalox.comLimited Warranty:Please refer to the Chromalox limited warr

Table of Contents1–Quick Setup ...12–Introduction ...

Chromalox 2110

2110 Temperature ControllerChromalox 21101Section 1—Quick SetupSection 1–Quick SetupAfter the controller is properly wired into the system, the user o

Chromalox 21102Section 2–IntroductionInspection and UnpackingYour Chromalox 2110 controller should arrive in good condition. Upon arrival, inspect the

2110 Temperature ControllerChromalox 2110 Model 2110 1/4 DIN Controller, with Selectable Thermocouple or RTD Inputs Code Control

Chromalox 21104Section 3–Installation and WiringSection 3—Installation and WiringSensor and Control Type Selection SwitchesSet the Chromalox 2110 cont

2110 Temperature ControllerChromalox 21105MountingTwo mounting collars securely hold the 2110 controller in the mounting hole. Remove these mounting c